Shenzhen Kai Mo Rui Electronic Technology Co. LTDShenzhen Kai Mo Rui Electronic Technology Co. LTD

News

SONY video conference camera operation steps

Source:Shenzhen Kai Mo Rui Electronic Technology Co. LTD2020-05-08

  Shenzhen Kaimorui Electronic Technology Co., Ltd. is a high-tech enterprise specializing in the application research, development, production and sales of video processing system products.


  1. The SONY D70P video conference camera supports remote IR infrared control, and also supports SONY-VISCA special protocol. Domestic products also support the PELCO-P/D protocol widely used in the surveillance industry. Therefore, the use of P/D protocol control brings great convenience to the hard disk video recorder and monitoring control keyboard! Because it adopts RS485 communication format, it can reach 1200 meters with twisted pair transmission. Compared with the SONY-VISCA protocol using RS232 transmission, it has great advantages!


  2. The default communication setting of the SONY D70P video conference camera is the SONY-VISCA protocol. If you want to use RS485-P/D protocol to control, you must switch the 4 digits 2 and 3 on the back to the ON position before powering on. The second place is the option of infrared remote control, and the third place is the choice of RS485/422 communication.


  Three, then start to connect the video cable, RS485 control cable, plug in the power supply, link the monitor and other preconditions.


  4. Turn on the socket power supply, the dome camera will start to perform power-on self-check after receiving power. At the same time, a blue screen appears on the monitor screen, and then the camera video image appears. The self-checking action takes about 10 seconds. After the self-inspection, the dome is in a state of waiting for command control.


  5. First use the random remote control to operate. First install 2 batteries of size 5 in the battery box on the back of the remote control, and then control the front or back of the D70P camera. SONY D70P is equipped with IR receiving ports on the front and rear. You must first press the white 1 channel of the remote control, and then press the direction navigation key of the remote control, then you can control the motion of the dome normally. If you want to set the No. 1 preset position, you need to hold down the PRESET button with your hand (hold it), then use the other hand to hold down the number 1, and then release it. At this time, the camera sets the current position to the No. 1 preset Bit. Call the No. 1 preset position and directly press the number 1 camera to immediately return to the set No. 1 position.


  6. The CLOSE of the remote control is used to exit the close menu, and M-OPEN is used to open the menu and confirm the function of exiting the menu.


  7. Now before PELCO-P/D protocol control, it is necessary to advance the D70P menu to set the parameters. Press the M-OPEN of the remote control once and the main menu SYSTEM SETUP will appear on the screen. Press the M-OPEN again to enter the single-line submenu. PROTOCOL: VISCA (SONY protocol). At this time, press SLOW and T twice to enter the third item PROTOCOL EDIT (protocol edit) of the sub-menu, press the M-OPEN key, the third sub-menu becomes ENABLE (valid ), press the SLOW-W key twice to return to the first item of the submenu, press M-OPEN once, the submenu will change to PROTOCOL:PELCO -D, select the D protocol, and then press the SLOW-T key to enter The second item of the submenu BAUD RATE (baud rate selection): 9600, the default is 2400, you must press M-OPEN twice to select 9600 baud rate (for P/D protocol control, you must select 9600 baud rate, use 12, 24 , 48 baud rate cannot be controlled). Then press the SLOW-T key to go to item 4 of the submenu, select the address, and the default number is 1. Finally press SLOW-T until the 12th item of the submenu appears EXIT AND SAVE:YES/NO (Exit and save: Yes/No), at this time press the M-OPEN key to return to the main menu, press the SLOW-W key to select EXIT MENU (exit the menu), press M-OPEN again to exit the menu successfully.


  8. After setting the SONY D70P menu above, select the control protocol of the control keyboard D, the address is 1, the baud rate is 9600. At this time, you can control all the SONY D70P's action functions through the monitoring keyboard, including the preset position. Settings, preset call, preset cruise and other functions.

Related News

Professional Engineer

24-hour online serviceSubmit requirements and quickly customize solutions for you

+8613798538021